X
 
  • Time
  • Show
Clear All
new posts
  • mega man
    Junior Member
    • Jul 2013
    • 15

    #16
    well suneagle that was the very same way i calculated them at first before actually using them, but after getting them and putting them to use i saw different results, kinda wondering why the manufacturer's rated them like that in the first place. using 4 of them give 24amps in good sun, which kinda had me confused at first use, weird part is i have some the same length but those rate 136watts and they give the exact same amp output as the ones rated at 68watts.

    20130709_094038.jpg

    i use these 4 to charge 4x 6v golf cart batteries that run the fridge and my electric stove
    Attached Files

    Comment

    • snelbaker
      Junior Member
      • Jul 2013
      • 6

      #17
      Originally posted by SunEagle
      That Thunderbolt CC only has a maximum input voltage of 25v. if was made for a 12 volt system. If you had wired your panels in parallel it would have been ok. Of course you still need to have gotten the correct wiring polarity.

      Whichever CC has let out the smoke is no longer good. Best to give up on it.
      may i send you pictures. they are too large to post.

      Comment

      • SunEagle
        Super Moderator
        • Oct 2012
        • 15163

        #18
        Originally posted by snelbaker
        may i send you pictures. they are too large to post.
        You should be able to Private Message me and add your pictures. What in particular are you sending?

        Comment

        • Mike90250
          Moderator
          • May 2009
          • 16020

          #19
          Unisolar panels degrade over time from sun exposure, so they produce a lot the first year or so, and in 5 years, will still output their nameplate power.
          Powerfab top of pole PV mount (2) | Listeroid 6/1 w/st5 gen head | XW6048 inverter/chgr | Iota 48V/15A charger | Morningstar 60A MPPT | 48V, 800A NiFe Battery (in series)| 15, Evergreen 205w "12V" PV array on pole | Midnight ePanel | Grundfos 10 SO5-9 with 3 wire Franklin Electric motor (1/2hp 240V 1ph ) on a timer for 3 hr noontime run - Runs off PV ||
          || Midnight Classic 200 | 10, Evergreen 200w in a 160VOC array ||
          || VEC1093 12V Charger | Maha C401 aa/aaa Charger | SureSine | Sunsaver MPPT 15A

          solar: http://tinyurl.com/LMR-Solar
          gen: http://tinyurl.com/LMR-Lister

          Comment

          • SunEagle
            Super Moderator
            • Oct 2012
            • 15163

            #20
            Originally posted by Mike90250
            Unisolar panels degrade over time from sun exposure, so they produce a lot the first year or so, and in 5 years, will still output their nameplate power.
            I know they come in different sizes but what is the nameplate info on the average size of one of these panels? I thought they had a very high voltage output but relatively low amp rating.

            Comment

            • Mike90250
              Moderator
              • May 2009
              • 16020

              #21
              The Unisolar 64 that I have is about a 20V panel. OK for 12V battery & PWM controller.
              Attached Files
              Powerfab top of pole PV mount (2) | Listeroid 6/1 w/st5 gen head | XW6048 inverter/chgr | Iota 48V/15A charger | Morningstar 60A MPPT | 48V, 800A NiFe Battery (in series)| 15, Evergreen 205w "12V" PV array on pole | Midnight ePanel | Grundfos 10 SO5-9 with 3 wire Franklin Electric motor (1/2hp 240V 1ph ) on a timer for 3 hr noontime run - Runs off PV ||
              || Midnight Classic 200 | 10, Evergreen 200w in a 160VOC array ||
              || VEC1093 12V Charger | Maha C401 aa/aaa Charger | SureSine | Sunsaver MPPT 15A

              solar: http://tinyurl.com/LMR-Solar
              gen: http://tinyurl.com/LMR-Lister

              Comment

              Working...